Keine Daten mit Fronius Primo GEN24 3.6

Alles was mit der Solaranzeige Image Installation und Betrieb zu tun hat. Einfache Konfiguration mit einem Gerät.

Moderator: Ulrich

D3nn3s
Beiträge: 6
Registriert: Di 22. Okt 2024, 19:50

Keine Daten mit Fronius Primo GEN24 3.6

Beitrag von D3nn3s »

Guten Abend hab das Projekt zum laufen bekommen aber leider bekomme ich keine daten und ich weis leider nicht warum ihr einige Infos die vielleicht helfen
- Datenquellen Fronius GEN24 FW Installiert: ROW 1.21.6-1
- Wechselrichter Primo GEN24 3.6 Plus
über ip/solar_api/GetAPIVersion.cgi
bekomme ich dies ausgeben

Code: Alles auswählen

{
   "APIVersion" : 1,
   "BaseURL" : "/solar_api/v1/",
   "CompatibilityRange" : "1.7-6"
}
eingeben habe ich bei der cfg
12 für fronius
die ip und den Port 80
wen ich aber dann über mcedit /var/www/log/solaranzeige.log
es ist ein 64g usb stick angeschlossen

Code: Alles auswählen

login as: pi

Linux solaranzeige 6.6.31+rpt-rpi-v8 #1 SMP PREEMPT Debian 1:6.6.31-1+rpt1 (2024                                                                                                                                                             -05-29) aarch64

Raspberry Pi Version 6.1.0  64Bit Basis    August  2024  [ Bookworm ]

Software Version 6.1.0b           update   September  2024
Last login: Sun Oct 27 20:08:21 2024 from 192.168.178.39
CPU Temperatur 53 °C

pi@solaranzeige:~ $ raspi-config
Script must be run as root. Try 'sudo raspi-config'
pi@solaranzeige:~ $ sudo raspi-config

Welcome to fdisk (util-linux 2.38.1).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.

This disk is currently in use - repartitioning is probably a bad idea.
It's recommended to umount all file systems, and swapoff all swap
partitions on this disk.


Command (m for help):
Disk /dev/sda: 58,2 GiB, 62495129600 bytes, 122060800 sectors
Disk model: Flash Disk
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0xa878ce8e

Device     Boot   Start       End   Sectors  Size Id Type
/dev/sda1          8192   1056767   1048576  512M  c W95 FAT32 (LBA)
/dev/sda2       1056768 122060799 121004032 57,7G 83 Linux

Command (m for help): Partition number (1,2, default 2):
Partition 2 has been deleted.

Command (m for help): Partition type
   p   primary (1 primary, 0 extended, 3 free)
   e   extended (container for logical partitions)
Select (default p): Partition number (2-4, default 2): First sector (2048-122060                                                                                                                                                             799, default 2048): Last sector, +/-sectors or +/-size{K,M,G,T,P} (1056768-12206                                                                                                                                                             0799, default 122060799):
Created a new partition 2 of type 'Linux' and of size 57,7 GiB.
Partition #2 contains a ext4 signature.

Command (m for help):
Disk /dev/sda: 58,2 GiB, 62495129600 bytes, 122060800 sectors
Disk model: Flash Disk
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0xa878ce8e

Device     Boot   Start       End   Sectors  Size Id Type
/dev/sda1          8192   1056767   1048576  512M  c W95 FAT32 (LBA)
/dev/sda2       1056768 122060799 121004032 57,7G 83 Linux

Command (m for help): The partition table has been altered.
Syncing disks.


Welcome to fdisk (util-linux 2.38.1).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.

This disk is currently in use - repartitioning is probably a bad idea.
It's recommended to umount all file systems, and swapoff all swap
partitions on this disk.


Command (m for help):
Disk /dev/sda: 58,2 GiB, 62495129600 bytes, 122060800 sectors
Disk model: Flash Disk
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0xa878ce8e

Device     Boot   Start       End   Sectors  Size Id Type
/dev/sda1          8192   1056767   1048576  512M  c W95 FAT32 (LBA)
/dev/sda2       1056768 122060799 121004032 57,7G 83 Linux

Command (m for help): Partition number (1,2, default 2):
Partition 2 has been deleted.

Command (m for help): Partition type
   p   primary (1 primary, 0 extended, 3 free)
   e   extended (container for logical partitions)
Select (default p): Partition number (2-4, default 2): First sector (2048-122060                                                                                                                                                             799, default 2048): Last sector, +/-sectors or +/-size{K,M,G,T,P} (1056768-12206                                                                                                                                                             0799, default 122060799):
Created a new partition 2 of type 'Linux' and of size 57,7 GiB.
Partition #2 contains a ext4 signature.

Command (m for help):
Disk /dev/sda: 58,2 GiB, 62495129600 bytes, 122060800 sectors
Disk model: Flash Disk
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0xa878ce8e

Device     Boot   Start       End   Sectors  Size Id Type
/dev/sda1          8192   1056767   1048576  512M  c W95 FAT32 (LBA)
/dev/sda2       1056768 122060799 121004032 57,7G 83 Linux

Command (m for help): The partition table has been altered.
Syncing disks.


Broadcast message from root@solaranzeige on pts/2 (Sun 2024-10-27 20:25:21 CET):

The system will reboot now!

pi@solaranzeige:~ $
login as: pi
pi@192.168.178.84's password:
Linux solaranzeige 6.6.31+rpt-rpi-v8 #1 SMP PREEMPT Debian 1:6.6.31-1+rpt1 (2024                                                                                                                                                             -05-29) aarch64

Raspberry Pi Version 6.1.0  64Bit Basis    August  2024  [ Bookworm ]

Software Version 6.1.0b           update   September  2024
Last login: Sun Oct 27 20:26:10 2024
CPU Temperatur 58 °C

pi@solaranzeige:~ $ mcedit /var/www/log/solaranzeige.log

pi@solaranzeige:~ $ user.config.php
-bash: user.config.php: Kommando nicht gefunden.
pi@solaranzeige:~ $ mcedit /var/www/log/solaranzeige.log
/var/www/log/solaranzeige.log   [BM--]  0 L:[921+43 964/1060] *(57198/63448b) 0010 0x00A                                                                                                                                               [*][X]
  'Model' => '"VIA Hub"',
  'Hotplug' => 'USB',
  'Vendor' => 'usb 0x2109 "VIA Labs, Inc."',
  'Device' => 'usb 0x3431 "Hub"',
  'Revision' => '"4.21"',
  'Driver' => '"hub"',
  'Speed' => '480 Mbps',
  'Module Alias' => '"usb:v2109p3431d0421dc09dsc00dp01ic09isc00ip00in00"',
  'Config Status' => 'cfg=new, avail=yes, need=no, active=unknown',
  'Attached to' => '#27 (Hub)',
)
27.10. 20:25:35    -Daten:
array (
  30 => 'USB 00.0: 10a00 Hub',
  '' => '',
  'Unique ID' => 'pBe4.djic47EFb5E',
  'Parent ID' => 'VCu0.m2lGPNk7Xc4',
  'SysFS ID' => '/devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb2/2-0:1.0',
  'SysFS BusID' => '2-0:1.0',
  'Hardware Class' => 'hub',
  'Model' => '"Linux Foundation 3.0 root hub"',
  'Hotplug' => 'USB',
  'Vendor' => 'usb 0x1d6b "Linux Foundation"',
  'Device' => 'usb 0x0003 "3.0 root hub"',
  'Revision' => '"6.06"',
  'Serial ID' => '"0000:01:00.0"',
  'Driver' => '"hub"',
  'Module Alias' => '"usb:v1D6Bp0003d0606dc09dsc00dp03ic09isc00ip00in00"',
  'Config Status' => 'cfg=new, avail=yes, need=no, active=unknown',
  'Attached to' => '#1 (USB Controller)',
)
27.10. 20:25:35    -USB Devices:
array (
  1 =>
  array (
    'Device' => '0x0003',
  ),
)
27.10. 20:25:35    -Regler: 12
27.10. 20:25:35    -Device: Ethernet wird in die user.config.php eingetragen.
27.10. 20:25:35    -Zeile gefunden. USB Device kann ausgetauscht werden. Index: 745   $USBRegler         = "Ethernet";
27.10. 20:25:35    -Zeile gefunden. Raspberry Modell kann eingetragen werden. Index: 764   $Platine = "Raspberry Pi 4 Model B Rev 1.4";
27.10. 20:25:35    -Es handelt sich um ein 64 Bit System.
27.10. 20:26:27 |----------------   Start  fronius_symo_serie.php    ---------------.
27.10. 20:26:27    -API Version: 1 CompatibilityRange noch unbekannt: 1.7-6
27.10. 20:26:27    -Modell = Fronius GEN 24
27.10. 20:26:28 *  -Daten zur lokalen InfluxDB [ solaranzeige ] gesendet..
27.10. 20:27:21    -OK. Datenübertragung erfolgreich.
27.10. 20:27:21    -WattstundenGesamtHeute: 0
27.10. 20:27:21 |----------------   Stop   fronius_symo_serie.php    ---------------.
27.10. 20:28:01 |----------------   Start  fronius_symo_serie.php    ---------------.
27.10. 20:28:01    -API Version: 1 CompatibilityRange noch unbekannt: 1.7-6
27.10. 20:28:01    -Modell = Fronius GEN 24
27.10. 20:28:02 *  -Daten zur lokalen InfluxDB [ solaranzeige ] gesendet..
27.10. 20:28:55    -OK. Datenübertragung erfolgreich.
27.10. 20:28:55    -WattstundenGesamtHeute: 0
27.10. 20:28:55 |----------------   Stop   fronius_symo_serie.php    ---------------.
Danke für die Hilfe im Voraus
Sorry für die Rechtschreibung :D

Benutzeravatar
Ulrich
Administrator
Beiträge: 6253
Registriert: Sa 7. Nov 2015, 10:33
Wohnort: Essen
Hat sich bedankt: 131 Mal
Danksagung erhalten: 845 Mal

Re: Keine Daten mit Fronius Primo GEN24 3.6

Beitrag von Ulrich »

Laut LOG Datei werden die Daten einwandfrei in die Datenbank "solaranzeige" geschrieben. Warum glaubst du, dass nichts ausgelesen wird?

Gebe bitte einmal auf der Konsole folgendes ein:

influx
use solaranzeige
select * from AC order by time desc limit 10
quit

Dann sollten die Daten in der Datenbank zu sehen sein.
-----------------------------------------------------
Ulrich . . . . . . . . [ Admin ]

D3nn3s
Beiträge: 6
Registriert: Di 22. Okt 2024, 19:50

Re: Keine Daten mit Fronius Primo GEN24 3.6

Beitrag von D3nn3s »

Grüße Ulrich es war mein Fehler hatte das Grafana in Home Assistent auf gemacht gehabt und habe es zu spät mit bekommen läuft wie eine 1
frage wen ich die Ifluxdb von Home Assistent jetzt umleite zu der solaranzeige könnte es zu Probleme kommen ? würde nämlich noch meine Heizung mit rein nehmen viessmann mit api Schnittstelle
Sorry für die Rechtschreibung :D

Benutzeravatar
Ulrich
Administrator
Beiträge: 6253
Registriert: Sa 7. Nov 2015, 10:33
Wohnort: Essen
Hat sich bedankt: 131 Mal
Danksagung erhalten: 845 Mal

Re: Keine Daten mit Fronius Primo GEN24 3.6

Beitrag von Ulrich »

Wenn es keine Namensgleichheit der Datenbank kommt, dann sollte es kein Problem geben.
-----------------------------------------------------
Ulrich . . . . . . . . [ Admin ]

Zurück zu „Image Installation [ Single-Regler Version ]“

Wer ist online?

Mitglieder in diesem Forum: Sonstige [Bot] und 2 Gäste